{"title":"PSI","description":"\u003cp\u003ePSI \/ Poly-Tuff liquid-applied waterproofing, carried by Latux. Primers, basecoats, membranes, topcoats and the detailing accessories that go with them, for decks, balconies, parking structures and below-grade work.\u003c\/p\u003e\u003cp\u003eAsk your Latux rep about contractor pricing and system recommendations.\u003c\/p\u003e","products":[{"product_id":"enviro-grip-pur-5","title":"Enviro-Grip PUR#5","description":"\u003cp\u003e\u003cstrong\u003eA fast-turnaround urethane-polyurea primer that grips exterior decks and pedestrian surfaces before your waterproofing goes down.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEnviro-Grip PUR#5 is a single-component aromatic urethane-polyurea primer built for outdoor, light-duty, and pedestrian deck areas. It soaks into the substrate, locks down surface dust, and gives your PSI waterproofing membrane a bonded base to build on. Moisture-cured chemistry sets predictably in the field with no mixing and no measuring.\u003c\/p\u003e\n\u003cp\u003eUse it on prepared concrete decks, balconies, walkways, and light pedestrian traffic areas that need a dependable bond coat ahead of membranes and topcoats. Roll or squeegee a thin, even film, respect the recoat window, and keep the job moving. Because it is a one-part product, there is no pot-life waste from over-mixing. Open the pail, prime, and move to the next stage.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 300 sq ft per gallon (varies with substrate porosity)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 78% by weight, 76% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDry film:\u003c\/strong\u003e 4 ± 1 mils per coat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCure:\u003c\/strong\u003e pot life 60 to 90 min, tack-free 1 to 2 hr, recoat within 6 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e 1.65 lb\/gal (198 g\/L)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1 gallon, 5 gallon, 55-gallon drum\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePair with the Enviro-Grip PSI membrane and topcoat system for a complete pedestrian deck buildout.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need to mix anything?\u003c\/strong\u003e\u003cbr\u003eNo. PUR#5 is single-component and moisture-cured. Stir and apply.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow long before I can recoat?\u003c\/strong\u003e\u003cbr\u003eTack-free in 1 to 2 hours, recoat within 6 hours. If you pass the window, scuff and reprime.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat surfaces does it prime?\u003c\/strong\u003e\u003cbr\u003ePrepared concrete and masonry decks, balconies, and pedestrian walkways.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it rated for heavy vehicle traffic?\u003c\/strong\u003e\u003cbr\u003eNo. PUR#5 is for light-duty and pedestrian areas. For medium-to-heavy traffic, use Enviro-Grip ep#2sc.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow much will I need?\u003c\/strong\u003e\u003cbr\u003ePlan for about 300 sq ft per gallon and adjust up on rough or porous decks.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/Enviro-Grip-PUR5-Data-Sheet.pdf?v=1786629828\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"5 Gallon","offer_id":48326494552282,"sku":"PT-ENVIRO-PUR5-5","price":253.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9425911873754__5Gallon.png?v=1786907985"},{"product_id":"enviro-grip-ep-2sc","title":"Enviro-Grip ep#2sc","description":"\u003cp\u003e\u003cstrong\u003eA two-component epoxy primer that bites into metal flashings and stands up to medium-to-heavy traffic.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEnviro-Grip ep#2sc is a two-component solvenated epoxy-polyamine penetrating primer. Side A (black) and Side B (white) mix 1 to 1 by volume and cure into a tough, chemically bonded base coat. The solvent carrier drives the resin into tight, dense substrates, so it grips where waterborne primers slip.\u003c\/p\u003e\n\u003cp\u003eReach for ep#2sc on metal flashings, transitions, and medium-to-heavy-duty traffic areas that demand more bond strength than a pedestrian primer delivers. It is the workhorse primer in the PSI system for tough surfaces. Mix only what your crew can place inside the pot life. The color shift from black and white to a uniform gray tells you the two sides are fully blended.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 300 sq ft per gallon (varies with substrate)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 90% by weight, 84% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDry film:\u003c\/strong\u003e 4 ± 1 mils\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMix ratio:\u003c\/strong\u003e 1 part A to 1 part B by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorking:\u003c\/strong\u003e pot life 60 to 90 min, recoat window 16 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e 100 g\/L (solvent content)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e two-part kit, 2 gallon and 10 gallon\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApprovals:\u003c\/strong\u003e the Enviro-Grip EP#2 primer is named in Miami-Dade County, Florida NOA No. 25-0604.15 (expires 03\/06\/2031) as Enviro-Grip #2, a primer of the Flexideck C-WD waterproofing system. Listed under test specification ASTM C836.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMiami-Dade Notice of Acceptance\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eMiami-Dade County, Florida NOA No. 25-0604.15, expires 03\/06\/2031 (March 6, 2031).\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEnviro-Grip ep#2sc is the low-VOC grade of PSI Enviro-Grip EP#2, the two-component liquid applied epoxy-polyamine primer that the Notice of Acceptance lists as Enviro-Grip #2 under test specification ASTM C836. The NOA covers the Flexideck C-WD waterproofing system from Polytuff Systems International as a whole on concrete decks, approved 06\/26\/2025. It is not an approval of the primer used on its own.\u003c\/p\u003e\n\u003cp\u003eThe NOA states that the system is designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code, to a maximum design pressure of -502.5 psf. Enviro-Grip #2 is the primer in the approved assembly that finishes with porcelain tile. It goes onto prepared concrete at 1 gallon of mixed Part A and Part B per 300 sq ft, applied by brush or phenolic core roller, to a minimum coating thickness of 3 dry mils, and is left to become tack free and free of puddling before the base coat. New concrete must be cured 14 to 28 days. The NOA specifies Enviro-Grip #1 for the assembly without a tile topping, so confirm which assembly you are building with your Latux rep before you order.\u003c\/p\u003e\n\u003cp\u003eThe NOA also requires, at Limitation 5, that the work be done by a contractor licensed for roofing and waterproofing who is a Manufacturer Trained Qualified Applicator approved and licensed by Polytuff Systems International. Latux is on that approved applicator list, so the company that supplies the system can also install it.\u003c\/p\u003e\n\u003cp\u003eThe full Notice of Acceptance is available on request.\u003c\/p\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePSI membranes and topcoats over metal and high-traffic concrete.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I mix it?\u003c\/strong\u003e\u003cbr\u003eCombine Side A (black) and Side B (white) 1 to 1 by volume and blend to a uniform gray.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I prime metal with it?\u003c\/strong\u003e\u003cbr\u003eYes. ep#2sc is built for metal flashings and dense substrates as well as medium-to-heavy traffic concrete.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the recoat window?\u003c\/strong\u003e\u003cbr\u003eUp to 16 hours. Beyond that, abrade before topcoating.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow long is the pot life?\u003c\/strong\u003e\u003cbr\u003e60 to 90 minutes depending on temperature. Mix in batches you can place in time.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat kit sizes are available?\u003c\/strong\u003e\u003cbr\u003eA 2-gallon kit and a 10-gallon kit, each with matched A and B sides.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/Enviro-Grip-ep2sc-Data-Sheet.pdf?v=1786629827\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"2 Gallon","offer_id":48326494748890,"sku":"PT-ENVIRO-EP2SC-2","price":146.03,"currency_code":"USD","in_stock":true},{"title":"10 Gallon","offer_id":48326494781658,"sku":"PT-ENVIRO-EP2SC-10","price":676.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-ep2sc.png?v=1786975809"},{"product_id":"enviro-grip-405fc","title":"Enviro-Grip 405Fc","description":"\u003cp\u003e\u003cstrong\u003eA 100%-solids, zero-VOC epoxy moisture barrier that holds back concrete vapor before flooring goes down.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEnviro-Grip 405Fc is a 100%-solids, zero-VOC epoxy primer that works as a moisture vapor barrier over concrete slabs. Mixed 2 parts A to 1 part B, it forms a dense film that reduces moisture vapor emission rate up to 25 lb, bringing an out-of-spec slab below the 3 lb per 1000 sq ft threshold so you can protect the finish you install over it.\u003c\/p\u003e\n\u003cp\u003eUse it on concrete that failed or is at risk on a calcium chloride or relative humidity test, ahead of resilient flooring, wood, or resin coatings. Coverage is driven by the moisture reading, so test the slab first and set your spread rate accordingly. Applied as a single coat at 10 to 16 mils wet, 405Fc has a short 20-minute pot life. Mix tight batches and keep a wet edge.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage by moisture test:\u003c\/strong\u003e 150 sq ft\/gal (under 10 lb or under 85% RH), 125 sq ft\/gal (10 to 15 lb), 100 sq ft\/gal (15 to 25 lb). Default 100 sq ft\/gal if the slab is untested.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 100%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e zero\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMix ratio:\u003c\/strong\u003e 2 parts A to 1 part B\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplied:\u003c\/strong\u003e 10 to 16 mils wet film, single coat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorking:\u003c\/strong\u003e pot life 20 min, recoat 48 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance:\u003c\/strong\u003e reduces MVER up to 25 lb, below the 3 lb per 1000 sq ft threshold\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePSI primers and finish systems, or as a moisture barrier under third-party flooring.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhen do I need a moisture barrier primer?\u003c\/strong\u003e\u003cbr\u003eWhen a calcium chloride or RH test shows the slab above the limit your flooring allows, or the slab is untested and at risk.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I set coverage?\u003c\/strong\u003e\u003cbr\u003eBy the moisture reading. Drier slabs cover more, wetter slabs need more product per square foot. Untested slabs default to 100 sq ft per gallon.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the mix ratio?\u003c\/strong\u003e\u003cbr\u003e2 parts A to 1 part B.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow long is the pot life?\u003c\/strong\u003e\u003cbr\u003eAbout 20 minutes. Mix small and keep moving.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhen can I install flooring over it?\u003c\/strong\u003e\u003cbr\u003eAfter the 48-hour recoat and cure window. Confirm against your finish system requirements.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/Enviro-Grip-405Fc-Data-Sheet.pdf?v=1786629827\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"3 Gallon","offer_id":48326495174874,"sku":"PT-ENVIRO-405FC-3","price":400.27,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-405fc.png?v=1786975810"},{"product_id":"enviro-grip-wbs","title":"Enviro-Grip WBs","description":"\u003cp\u003e\u003cstrong\u003eA low-odor waterborne epoxy primer that grips concrete, wood, modified bitumen, and asphalt.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEnviro-Grip WBs is a waterborne, low-VOC, low-odor epoxy primer for interior and enclosed work where solvent smell is a problem. It ties into a wide range of substrates including concrete, wood, modified bitumen, and asphalt, which makes it a flexible bond coat across roofing and deck details.\u003c\/p\u003e\n\u003cp\u003eWBs is a three-part product: resin, hardener, and water. Combine the resin and hardener, then thin with the specified water to reach application viscosity. Roll or spray a thin, even film and let it develop before topcoating. Because it is water-based, it will not tolerate freezing. Store and apply above freezing and protect fresh film from frost.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 300 to 450 sq ft per gallon (varies with substrate porosity)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 48.8% by weight, 46.8% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMix:\u003c\/strong\u003e three parts (resin + hardener + water)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorking:\u003c\/strong\u003e pot life 45 to 60 min, recoat 8 to 24 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e 24 g\/L\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStorage:\u003c\/strong\u003e must not freeze\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePSI membranes and topcoats over concrete, wood, and bituminous substrates.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhy choose a waterborne primer?\u003c\/strong\u003e\u003cbr\u003eLow odor and low VOC for interior, occupied, or poorly ventilated spaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat can I prime with it?\u003c\/strong\u003e\u003cbr\u003eConcrete, wood, modified bitumen, and asphalt.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I mix it?\u003c\/strong\u003e\u003cbr\u003eCombine resin and hardener, then add the specified water to reach spray or roll viscosity.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan it freeze in storage?\u003c\/strong\u003e\u003cbr\u003eNo. Keep it above freezing. Frozen product is ruined.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the recoat window?\u003c\/strong\u003e\u003cbr\u003e8 to 24 hours depending on temperature and humidity.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow is it priced?\u003c\/strong\u003e\u003cbr\u003ePricing for WBs is set through your Latux rep and is not posted here yet. Contact us for a quote.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/Enviro-Grip-WBs-Data-Sheet.pdf?v=1786629827\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"3.5 Gallon","offer_id":48326495568090,"sku":null,"price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-wbs.png?v=1786975809"},{"product_id":"enviro-grip-wbm","title":"Enviro-Grip WBM","description":"\u003cp\u003e\u003cstrong\u003eA water-based moisture primer built to bond over asphalt.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEnviro-Grip WBM is a water-based moisture and membrane primer used over asphalt surfaces. It is a two-component product, Side A (yellow) and Side B (off-white), formulated to prepare asphalt substrates for the PSI waterproofing buildout.\u003c\/p\u003e\n\u003cp\u003eReach for WBM when the job calls for a water-based primer over asphalt ahead of the membrane. As a low-odor waterborne product, it suits work where solvent primers are not practical.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eData note:\u003c\/strong\u003e the manufacturer technical data sheet for WBM was not available when this listing was built. Coverage, solids, cure, and VOC figures are being confirmed with the manufacturer. Contact your Latux rep for current application data and job-specific guidance before you spec WBM.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e water-based, two-component moisture and membrane primer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComponents:\u003c\/strong\u003e Side A (yellow) and Side B (off-white)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubstrate:\u003c\/strong\u003e asphalt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage, solids, cure, VOC:\u003c\/strong\u003e published data sheet pending, confirm with your Latux rep\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePSI membranes and topcoats over asphalt.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is WBM for?\u003c\/strong\u003e\u003cbr\u003ePriming asphalt surfaces with a water-based moisture and membrane primer ahead of the PSI waterproofing system.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow is it packaged?\u003c\/strong\u003e\u003cbr\u003eAs a two-part product, Side A (yellow) and Side B (off-white).\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhere are the full specs?\u003c\/strong\u003e\u003cbr\u003eThe manufacturer data sheet is being finalized. Contact your Latux rep for verified coverage and cure data.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it solvent-based?\u003c\/strong\u003e\u003cbr\u003eNo. WBM is water-based, which keeps odor low.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it over concrete?\u003c\/strong\u003e\u003cbr\u003eWBM is specified for asphalt. For concrete, ask your Latux rep about the right PSI primer.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"5 Gallon","offer_id":48326495699162,"sku":"PT-ENVIRO-WBM-5","price":441.19,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9425912561882__5Gallon.png?v=1786908599"},{"product_id":"b-tuff-302","title":"B-Tuff 302 NG","description":"\u003cp\u003e\u003cstrong\u003eAn economical single-component, moisture-cured urethane basecoat that builds a seamless waterproofing membrane on concrete, plywood, and metal.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eB-Tuff 302 NG is a liquid-applied, moisture-cured, flexible aromatic-urethane basecoat carried by Latux from the PSI\/Poly-Tuff waterproofing line. It is the value-focused base membrane in the range: one component, easy to premix and squeegee out, and proven over prepared concrete, masonry, plywood, wood, and metal. A low-VOC SC grade is available where 100 g\/L limits apply.\u003c\/p\u003e\n\u003cp\u003eApply a continuous, even coat across the deck at roughly 50 to 60 sq ft per gallon, detail joints and cracks with reinforcement tape and sealant, and let it moisture-cure before topcoating. Add B-Tuff 302 Accelerator when the schedule calls for a faster turn. As with all PSI base membranes, it is covered by a wear-rated topcoat rather than left exposed.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry:\u003c\/strong\u003e single-component, moisture-cured aromatic-urethane basecoat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Grey or Tan\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 81% by weight, 71% by volume (standard grade)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardness:\u003c\/strong\u003e Shore A 55 ± 5 (ASTM D-2240)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTensile strength:\u003c\/strong\u003e 800 ± 100 psi (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElongation:\u003c\/strong\u003e 500 ± 50% (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e 2.01 lb\/gal (240 g\/L) standard; low-VOC SC grade at 0.78 lb\/gal (94 g\/L)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 50 to 60 sq ft per gallon per coat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCure:\u003c\/strong\u003e 12 to 16 hr, or 6 to 8 hr with accelerator (75F \/ 50% RH)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubstrates:\u003c\/strong\u003e concrete, masonry, plywood, wood, metal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1 gallon, 5 gallon; 55-gallon drum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShelf life:\u003c\/strong\u003e 6 months, factory-sealed, stored 60 to 95F; contains isocyanates and solvents\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePrime with an Enviro-Grip PSI primer (EP#1, EP#2, or PUR#555 for recoats), bridge joints and cracks with PTS E-101 and reinforcement tape, and finish with a PSI topcoat. Add B-Tuff 302 Accelerator for faster cure.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat makes 302 the economical choice?\u003c\/strong\u003e\u003cbr\u003eIt is a straightforward single-component moisture-cured basecoat. There is no mixing of parts, and it covers a wide range of substrates, which keeps material and labor simple on budget-driven jobs.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow long before I can recoat?\u003c\/strong\u003e\u003cbr\u003ePlan 12 to 16 hours to cure, or 6 to 8 hours if you add B-Tuff 302 Accelerator. If more than 24 hours pass between coats, reprime first.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich grade do I need for low-VOC areas?\u003c\/strong\u003e\u003cbr\u003eThe standard grade is 240 g\/L VOC. Where regulations cap VOC near 100 g\/L, use the 302SC low-VOC grade. Confirm local codes before you order.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat coverage should I plan for?\u003c\/strong\u003e\u003cbr\u003eAbout 50 to 60 sq ft per gallon per coat, adjusted for surface profile and porosity.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs a topcoat required?\u003c\/strong\u003e\u003cbr\u003eYes. B-Tuff 302 NG is a base membrane only. It cannot take direct wear or abrasion and must be topcoated.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/B-Tuff-302-Data-Sheet.pdf?v=1786631786\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"5 Gallon","offer_id":48326495797466,"sku":"PT-BTUFF-302-5","price":230.05,"currency_code":"USD","in_stock":true},{"title":"1 Gallon","offer_id":48337451548890,"sku":"PT-BTUFF-302-1","price":46.01,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9425912660186__5Gallon.png?v=1786908603"},{"product_id":"b-tuff-308","title":"B-Tuff 308","description":"\u003cp\u003e\u003cstrong\u003eA two-component, fast-setting polyurea-urethane basecoat that reinforces while wet and cures rapidly, even in cold weather.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eB-Tuff 308 is a solvent-free, high-solids hybrid polyurea urethane waterproofing membrane carried by Latux from the PSI\/Poly-Tuff line. Side A (dark grey) and Side B (black) are premeasured and mixed on site to build a seamless, flexible base membrane over prepared concrete, plywood, or metal. With a short pot life and fast gel, it can be placed in a single pass or multiple coats and applied in temperatures as low as 20F, so crews keep moving when other basecoats stall.\u003c\/p\u003e\n\u003cp\u003eThe membrane can be fully reinforced with fabric while still wet, which speeds detailing at joints, drains, and flashings. It is relatively insensitive to moisture and temperature, making it a strong choice for pedestrian walkways, patios, stairways, sun decks, balconies, mechanical rooms, wash racks, kennel runs, and vehicular-traffic areas. Because pot life is short, mix only what the crew can place and reinforce immediately.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry:\u003c\/strong\u003e two-component, solvent-free hybrid polyurea urethane basecoat membrane\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Grey (Side A dark grey, Side B black)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMix:\u003c\/strong\u003e premeasured kits, Side A to Side B, do not dilute or estimate\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 94% by weight, 95% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardness:\u003c\/strong\u003e Shore A 80 ± 3 (ASTM D-2240)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTensile strength:\u003c\/strong\u003e 2,500 ± 100 pli (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElongation:\u003c\/strong\u003e 800 ± 100% (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePot life:\u003c\/strong\u003e 10 ± 2 min at 75F \/ 50% RH\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTack-free:\u003c\/strong\u003e 3 to 4 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-temp application:\u003c\/strong\u003e down to 20F (-6.7C)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e under 0.49 lb\/gal (59 g\/L)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 1,520 sq ft per gallon at 1 mil (theoretical; varies with build)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompliance:\u003c\/strong\u003e contains isocyanates\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1-gallon kit (Side A 0.8 gal + Side B 0.2 gal); 5-gallon kit (Side A 4 gal + Side B 1 gal)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShelf life:\u003c\/strong\u003e 12 months, factory-sealed, stored 60 to 95F\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePrime with the recommended Enviro-Grip PSI primer, detail joints and cracks with PTS E-101 sealant and reinforcement tape, and topcoat with a PSI wear coat. Order Side A and Side B in matching kit sizes so the premeasured ratio stays correct.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhy are Side A and Side B sold separately?\u003c\/strong\u003e\u003cbr\u003eSo you can restock a single component if you run short. The kit ratio is premeasured, so pair Side A and Side B in the same kit size (1-gallon or 5-gallon) to keep it correct. Never estimate or dilute.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow long is the pot life?\u003c\/strong\u003e\u003cbr\u003eAbout 10 minutes at 75F. Mix only what you can spread and reinforce right away, and do not open the parts until you are ready to apply.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it in cold weather?\u003c\/strong\u003e\u003cbr\u003eYes. It is formulated for application down to 20F, which is well below most single-component basecoats.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I embed fabric while it is wet?\u003c\/strong\u003e\u003cbr\u003eYes. B-Tuff 308 can be fully reinforced while wet, which makes flashing and detail work faster.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it a finished surface?\u003c\/strong\u003e\u003cbr\u003eNo. It is a base membrane and must be topcoated. It is not built to take direct wear, abrasion, or direct sun on its own.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/B-Tuff-308-Data-Sheet.pdf?v=1786631786\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"5 Gallon Kit","offer_id":48326496059610,"sku":"PT-BTUFF-308-5","price":314.17,"currency_code":"USD","in_stock":true},{"title":"1 Gallon Kit","offer_id":48337451483354,"sku":"PT-BTUFF-308-1","price":63.69,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9425912791258__5Gallon.png?v=1786908607"},{"product_id":"t-shield-wc-100","title":"T-Shield WC 100","description":"\u003cp\u003e\u003cstrong\u003eA single-component, high-solids waterproofing membrane that installs at any thickness from 30 to 2,500 mils in one pass, on green concrete or cured.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eT-Shield WC-100 is a water-catalyzed, bitumen-modified, coal-tar-free urethane-polyurea membrane carried by Latux from the PSI\/Poly-Tuff line. It builds a seamless, joint-free, crack-free waterproofing layer for below-grade and between-slab work and can be applied to green concrete just 24 hours after the pour. One product covers both horizontal and vertical surfaces: order the Horizontal grade for decks, floors, and slabs, and the Vertical grade for walls, foundations, and planters where the material has to hold on a slope without sagging.\u003c\/p\u003e\n\u003cp\u003eBecause it is high-solids and cures throughout the film, WC-100 fills ponds and low spots, re-slopes drains from negative to positive, and reaches heavy dry-film builds in a single application without kettles or heat. It meets the criteria of ASTM C-836 and E-96, resists bacterial growth, and stays flexible across a wide temperature range. Typical uses include foundation walls, basements, planters, green roofs, tunnels, showers and wet areas, and plaza and promenade decks.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry:\u003c\/strong\u003e single-component, high-solids, water-catalyzed, bitumen-modified urethane-polyurea membrane (coal-tar free)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrades:\u003c\/strong\u003e Horizontal (self-leveling) and Vertical (non-sag)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 95% by weight, 94% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardness:\u003c\/strong\u003e Shore A 25 ± 5 (ASTM D-2240)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTensile strength:\u003c\/strong\u003e 300 ± 50 psi (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElongation:\u003c\/strong\u003e 650 ± 50% (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuild:\u003c\/strong\u003e 30 to 2,500 mils in a single application\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e min. 60 dry mils on concrete, 90 on plywood; 120 to 160 mils for extended warranty\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e under 0.5 lb\/gal (under 60 g\/L)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandards:\u003c\/strong\u003e meets criteria of ASTM C-836 and E-96; resistant to bacterial growth\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGreen concrete:\u003c\/strong\u003e apply 24 hr after pour\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1 gallon, 5 gallon; 55-gallon drum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShelf life:\u003c\/strong\u003e 12 months, factory-sealed, stored 60 to 95F; contains isocyanates\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePrime per the datasheet with Enviro-Grip EP#2, EP#1, or PUR#555, reinforce joints and cracks with Polyester or Max Fabric tape, and mix with water (one to two quarts per 5 gallons) before applying. For hydrostatic conditions, prime first with Enviro-Grip 405FC.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the difference between the Horizontal and Vertical grades?\u003c\/strong\u003e\u003cbr\u003eBoth are the same WC-100 chemistry. Horizontal is self-leveling for decks, floors, and slabs; Vertical is non-sag so it stays put on walls, foundations, and planters. Pick the grade that matches the surface.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I really apply it over green concrete?\u003c\/strong\u003e\u003cbr\u003eYes. WC-100 can be applied to green concrete 24 hours after the pour, which pulls waterproofing forward in the schedule.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow thick can one coat go?\u003c\/strong\u003e\u003cbr\u003eAnywhere from 30 to 2,500 mils in a single application. It cures through the film, so you can fill low areas and re-slope to drain in one pass.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I mix it with anything?\u003c\/strong\u003e\u003cbr\u003eYes. Blend with water at one to two quarts per 5-gallon pail to catalyze the cure. Do not dilute beyond that or whip air into the material.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it a wearing surface?\u003c\/strong\u003e\u003cbr\u003eNo. It is a waterproofing membrane, not UV stable, and cannot take direct wear or abrasion. Cover it per the system specification.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/T-Shield-WC-100-Data-Sheet.pdf?v=1786631786\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"Horizontal 5 Gallon","offer_id":48326496452826,"sku":"PT-TS-WC100H-5","price":176.65,"currency_code":"USD","in_stock":true},{"title":"Vertical 5 Gallon","offer_id":48326496485594,"sku":"PT-TS-WC100V-5","price":184.71,"currency_code":"USD","in_stock":true},{"title":"Horizontal 1 Gallon","offer_id":48337451581658,"sku":"PT-TS-WC100H-1","price":40.71,"currency_code":"USD","in_stock":false},{"title":"Vertical 1 Gallon","offer_id":48337451614426,"sku":"PT-TS-WC100V-1","price":42.37,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9425913053402__5Gallon.png?v=1786908611"},{"product_id":"p-tuff-classic","title":"P-Tuff Classic","description":"\u003cp\u003e\u003cstrong\u003eA single-component, water-catalyzed polyurethane basecoat that builds a seamless waterproofing membrane at any thickness in one pass.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eP-Tuff Classic is a solvent-free, non-gassing, liquid-applied elastomeric basecoat carried by Latux as part of the PSI\/Poly-Tuff waterproofing system. It goes down in a single application from a feather edge up to 3 inches deep and cures simultaneously throughout the film in roughly 4 hours at 75F and 50% relative humidity. That makes it the workhorse coat for rough, textured, or sloped decks and for filling ponding areas where a thick, monolithic membrane is needed.\u003c\/p\u003e\n\u003cp\u003eMix the pail, catalyze with water at a 4:1 ratio, and squeegee or trowel an even coat across the deck. Broadcast rubber granules or silica sand into the wet membrane for slip resistance, then cure and topcoat. Because P-Tuff Classic holds high tensile strength and elongation, it stands up on bridges, plaza decks, balconies, mechanical rooms, and pedestrian and light-auto traffic areas. An optional accelerator vial shortens cure time in cold conditions.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry:\u003c\/strong\u003e single-component, water-catalyzed polyurethane elastomeric basecoat, solvent free and non-gassing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e White\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 95% by weight, 93% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardness:\u003c\/strong\u003e Shore A 60 ± 5 (ASTM D-2240)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTensile strength:\u003c\/strong\u003e 1,350 ± 150 psi (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElongation:\u003c\/strong\u003e 675 ± 50% (ASTM D-412)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e under 0.5 lb\/gal (under 60 g\/L)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCure:\u003c\/strong\u003e approx. 4 hr at 75F \/ 50% RH; recoat 2 to 24 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuild:\u003c\/strong\u003e feather edge up to 3 in (7.6 cm) in a single application\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 1,488 sq ft per gallon at 1 mil (theoretical; varies with build thickness)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApprovals:\u003c\/strong\u003e named in Miami-Dade County, Florida NOA No. 25-0604.15 (expires 03\/06\/2031) as the base coat of the Flexideck C-WD waterproofing system. Listed under test specification ASTM C-957.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1 gallon and 5 gallon (each ships with catalyst), plus separate catalyst vials; 55-gallon drum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShelf life:\u003c\/strong\u003e 6 months, factory-sealed, stored 60 to 95F; contains isocyanates\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMiami-Dade Notice of Acceptance\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eMiami-Dade County, Florida NOA No. 25-0604.15, expires 03\/06\/2031 (March 6, 2031).\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eP-Tuff Classic is named in that Notice of Acceptance as the base coat of the Flexideck C-WD waterproofing system from Polytuff Systems International, approved 06\/26\/2025. The acceptance covers the assembly as a whole on concrete decks. It is not an approval of the base coat used on its own.\u003c\/p\u003e\n\u003cp\u003eThe NOA states that the system is designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code, to a maximum design pressure of -502.5 psf. Both approved assemblies place P-Tuff Classic over an Enviro-Grip primer at 2 1\/2 gallons per 100 sq ft, with 16-30 mesh clean silica sand broadcast into the wet base coat at 20 pounds per 100 sq ft till refusal. Minimum coating thickness is 32 ± 2 dry mils in the assembly without tile, on minimum 3000 psi concrete, and 40 ± 2 dry mils in the assembly with porcelain tile, on minimum 2500 psi concrete. New concrete must be cured 14 to 28 days, and an integrity test to ASTM D 5957 by an approved lab is required.\u003c\/p\u003e\n\u003cp\u003eThe NOA also requires, at Limitation 5, that the work be done by a contractor licensed for roofing and waterproofing who is a Manufacturer Trained Qualified Applicator approved and licensed by Polytuff Systems International. Latux is on that approved applicator list, so the company that supplies the system can also install it.\u003c\/p\u003e\n\u003cp\u003eThe full Notice of Acceptance is available on request.\u003c\/p\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePrime first with an Enviro-Grip PSI primer, treat joints and cracks with PTS E-101 sealant and reinforcement tape, then finish with a PSI topcoat. Add a P-Tuff Catalyst vial for faster cure in cold weather (up to 3 vials per 5 gallons).\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eHow thick can I apply it in one coat?\u003c\/strong\u003e\u003cbr\u003eFrom a feather edge up to 3 inches. It cures through the full film, so you can fill ponding areas and slope to drain in a single pass.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I have to add the catalyst?\u003c\/strong\u003e\u003cbr\u003eNo. P-Tuff Classic is water-catalyzed and cures on its own. The separate catalyst vial is optional and used to speed cure in cold or low-humidity conditions.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the mix ratio?\u003c\/strong\u003e\u003cbr\u003eBlend pre-accelerated P-Tuff Classic with water at 4:1 by volume (about 1.25 gallons of water per 5-gallon pail) until fully combined.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it a finished wearing surface?\u003c\/strong\u003e\u003cbr\u003eNo. This is a base membrane only. It is not UV stable and must be covered with a PSI topcoat. Broadcast aggregate for slip resistance before topcoating.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhere should I not use it?\u003c\/strong\u003e\u003cbr\u003eNot for below-grade or on-grade slabs, hydrostatic conditions, or pools without the correct Enviro-Grip moisture primer. Concrete should be 3,000 psi minimum and profiled to ICRI CSP 2-3.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/P-Tuff-Classic-Data-Sheet.pdf?v=1786631786\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"5 Gallon","offer_id":48326496846042,"sku":"PT-CLASSIC-5","price":279.01,"currency_code":"USD","in_stock":true},{"title":"1 Gallon","offer_id":48337451385050,"sku":"PT-CLASSIC-1","price":61.18,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9425913217242__5Gallon.png?v=1786908614"},{"product_id":"top-shield-5600ef","title":"Top-Shield 5600ef","description":"\u003cp\u003e\u003cstrong\u003eA two-component, low-odor, high-solids aliphatic topcoat that finishes your deck with a fast-curing, UV-stable wear layer rated for foot and vehicle traffic.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eTop-Shield 5600EF is a two-component, hybrid aliphatic-elastomeric topcoat that lays down the finished wear surface over a PSI waterproofing membrane. It sets fast, cures in hours, and stands up to heavy-duty vehicular decks and ramps as well as pedestrian balconies and breezeways. Formulated to meet ASTM C-957, it delivers a non-gassing finish on properly prepared interior or exterior concrete, plywood, and metal.\u003c\/p\u003e\n\u003cp\u003eMix Side-A (medium grey) with Side-B (clear) at a 10:1 ratio, then pull it across the deck with a notched squeegee or trowel. It goes down in temperatures as low as 20°F and recoats within 24 hours, so crews keep moving. Low odor and very low VOC (under 60 g\/L) make it a fit for occupied buildings, mechanical rooms, and kennels. Carried by Latux, this is the topcoat that closes out a PSI deck system built to last.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Two-component hybrid aliphatic-elastomeric topcoat (Side-A medium grey, Side-B clear)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMix ratio:\u003c\/strong\u003e 10:1 (Side-A to Side-B)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDry film:\u003c\/strong\u003e 14 ± 2 mils per coat at about 100 sq ft per gallon\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 88% by weight, 87% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCure:\u003c\/strong\u003e pot life 30 ± 10 min, cures in 2 to 4 hr, recoat within 24 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhysicals:\u003c\/strong\u003e Shore A 85 ± 5, tensile 3200 psi, elongation 450%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e under 0.5 lb\/gal (under 60 g\/L)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUV stability:\u003c\/strong\u003e 2000 hr Weather-O-Meter, no cracking or crazing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApprovals:\u003c\/strong\u003e named in Miami-Dade County, Florida NOA No. 25-0604.15 (expires 03\/06\/2031) as the top coat of the Flexideck C-WD waterproofing system. Meets ASTM C-957.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 4.4-gallon kit (4-gallon Side-A pail plus 0.4-gallon Side-B jar)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMiami-Dade Notice of Acceptance\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eMiami-Dade County, Florida NOA No. 25-0604.15, expires 03\/06\/2031 (March 6, 2031).\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eTop-Shield 5600EF is named in that Notice of Acceptance as the top coat of the Flexideck C-WD waterproofing system from Polytuff Systems International, approved 06\/26\/2025. The acceptance covers the assembly as a whole on concrete decks. It is not an approval of the top coat used on its own.\u003c\/p\u003e\n\u003cp\u003eThe NOA states that the system is designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code, to a maximum design pressure of -502.5 psf. In the approved assembly without a tile topping, Top-Shield 5600EF goes on over the base coat at 1 gallon per 100 sq ft, to a minimum coating thickness of 14 ± 2 dry mils. An integrity test to ASTM D 5957 by an approved lab is required.\u003c\/p\u003e\n\u003cp\u003eThe NOA also requires, at Limitation 5, that the work be done by a contractor licensed for roofing and waterproofing who is a Manufacturer Trained Qualified Applicator approved and licensed by Polytuff Systems International. Latux is on that approved applicator list, so the company that supplies the system can also install it.\u003c\/p\u003e\n\u003cp\u003eThe full Notice of Acceptance is available on request.\u003c\/p\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eApply over a cured PSI basecoat and membrane system for a complete pedestrian or vehicular deck buildout. Use Enviro-Grip PUR#555 for intercoat adhesion over existing urethane coatings.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eIs this a one-coat or two-coat product?\u003c\/strong\u003e\u003cbr\u003eEither. Top-Shield 5600EF is suitable for single or multiple applications. Follow your PSI guide spec for the system and coverage rate.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the mix ratio?\u003c\/strong\u003e\u003cbr\u003e10:1, Side-A to Side-B. Pre-mix Side-A, add Side-B, and blend to a uniform color. Pot life is about 30 minutes, so mix only what your crew can place.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan it take vehicle traffic?\u003c\/strong\u003e\u003cbr\u003eYes. It is rated for heavy-duty vehicular decks and ramps, plus pedestrian balconies, breezeways, mechanical rooms, and kennels. Allow 72 hours before heavy or vehicular traffic.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow cold can I apply it?\u003c\/strong\u003e\u003cbr\u003eDown to 20°F (-6.7°C). It is sensitive to heat and humidity, both of which speed the cure, so adjust batch sizes accordingly.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat color is it?\u003c\/strong\u003e\u003cbr\u003eSide-A is medium grey and Side-B is clear. Mixed, it finishes grey. Custom colors are available on minimum orders. Recoat within 24 hours for proper adhesion between coats.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.polytuffus.com\/pdf\/Topcoats\/3.4.7%20TOPSHIELD-5600-EF-190328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"4.4 Gallon Kit","offer_id":48326497337562,"sku":"PT-TOP-5600EF-LG","price":327.74,"currency_code":"USD","in_stock":true},{"title":"0.88 Gallon Kit","offer_id":48337470226650,"sku":"PT-TOP-5600EF-SM","price":70.28,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-5600ef.png?v=1786975810"},{"product_id":"top-shield-alp-150","title":"Top-Shield ALP 150","description":"\u003cp\u003e\u003cstrong\u003eA single-component, economical aliphatic urethane topcoat that reseals and protects concrete and plywood decks with a UV-stable, weatherable finish.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eTop-Shield ALP-150 is a single-component, moisture-cured aliphatic urethane topcoat built for pedestrian decks and for resealing existing urethane surfaces. It rolls or sprays on straight from the pail with no mixing, cures with ambient moisture, and holds excellent color retention and weatherability outdoors. With a Solar Reflective Index of 90, it helps keep coated decks cooler and cleaner.\u003c\/p\u003e\n\u003cp\u003eUse it as the finished wear layer over a PSI deck system, or to refresh a sound existing urethane coating. Apply at about 1 gallon per 100 sq ft for a 12 mil dry film, then recoat within 48 hours. It is UV stable and color-stable, so exterior balconies, walkways, and plywood decks stay looking sharp. Carried by Latux, ALP-150 is the economical topcoat choice when you need weatherability without a two-part mix.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Single-component, moisture-cured aliphatic urethane topcoat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e about 100 sq ft per gallon per coat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDry film:\u003c\/strong\u003e 12 ± 2 mils per coat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 80% by weight, 74% by volume (250 VOC grade)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhysicals:\u003c\/strong\u003e Shore A 90 ± 5, tensile 2700 psi, tear 400 pli, elongation 200%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolar Reflective Index:\u003c\/strong\u003e 90\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCure:\u003c\/strong\u003e 16 hr between coats, recoat within 48 hr\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVOC:\u003c\/strong\u003e 1.87 lb\/gal (225 g\/L); SC grade available at 0.83 lb\/gal (99 g\/L)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e grey shades, tan, and chocolate custom on minimum order\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 5-gallon pail (also 1-gallon can and 55-gallon drum)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eApply over a cured PSI basecoat and membrane system, or as a resealer over sound existing urethane. Prime with Enviro-Grip 404FC where moisture or hydrostatic pressure is a concern.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDo I mix anything?\u003c\/strong\u003e\u003cbr\u003eNo. ALP-150 is single-component and moisture-cured. Mix the pail on its own for about 5 minutes to a uniform color, then apply.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is it used for?\u003c\/strong\u003e\u003cbr\u003ePedestrian decks on concrete and plywood, most metal, wood, and masonry surfaces, and resealing existing urethane surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow many coats do I need?\u003c\/strong\u003e\u003cbr\u003eOften more than one, depending on the system spec. Apply about 1 gallon per 100 sq ft per coat and recoat within 48 hours for proper adhesion.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs there a low-VOC version?\u003c\/strong\u003e\u003cbr\u003eYes. ALP-150(SC) meets 150 VOC at 0.83 lb\/gal for jurisdictions with tighter limits. Confirm the grade required at your job site.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it UV stable?\u003c\/strong\u003e\u003cbr\u003eYes. It is aliphatic with excellent weatherability, good color retention, and a Solar Reflective Index of 90. Note it has limited chemical resistance and can flatten or stain over time.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.polytuffus.com\/pdf\/Topcoats\/3.4.3%20TOPSHIELD-ALP-150-190328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"5 Gallon","offer_id":48326497566938,"sku":null,"price":346.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9425913675994__5Gallon.png?v=1786908619"},{"product_id":"topshield-m1-gloss","title":"Topshield M1 Gloss","description":"\u003cp\u003e\u003cstrong\u003eA single-component, high-gloss aliphatic topcoat that puts a tough, UV-stable wear layer over your deck waterproofing system.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eTopshield M1 Gloss is the final protective finish for pedestrian and vehicular traffic-deck coatings. It goes down as a liquid-applied, moisture-cured film that seals and shields the polyurethane or polyurea membrane underneath, then hardens into a high-gloss surface built to take foot traffic, tires, and weather. As an aliphatic topcoat it holds its look outdoors, resisting yellowing, chalking, and gloss fade where a standard finish would break down.\u003c\/p\u003e\n\u003cp\u003eUse it as the last coat over prepared basecoat and membrane systems on balconies, walkways, parking decks, ramps, and exposed traffic surfaces. Because it is a one-part product, there is no mixing and no measuring. Open the pail, roll or squeegee a thin even film, respect the recoat window, and keep the job moving to the next stage.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e single-component, moisture-cured aliphatic topcoat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e high gloss\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUV performance:\u003c\/strong\u003e UV-resistant, resists yellowing, chalking, and gloss fade\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDurability:\u003c\/strong\u003e tough abrasion and wear resistance for pedestrian and vehicular traffic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRole:\u003c\/strong\u003e final wear layer and protective seal over polyurethane and polyurea deck membranes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e liquid-applied by roller or squeegee, no mixing required\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1 gallon, 5 gallon\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eApply as the finish coat over PSI basecoat and membrane systems to complete a pedestrian or vehicular traffic-deck buildout.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need to mix anything?\u003c\/strong\u003e\u003cbr\u003eNo. Topshield M1 Gloss is single-component and moisture-cured. Stir and apply.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat does the topcoat do?\u003c\/strong\u003e\u003cbr\u003eIt is the wear layer. It seals and protects the membrane below and gives you a hard, high-gloss surface that stands up to traffic and weather.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it yellow or fade in sunlight?\u003c\/strong\u003e\u003cbr\u003eNo. It is an aliphatic finish, so it holds gloss and color outdoors and resists yellowing, chalking, and fade far better than a non-aliphatic topcoat.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhere should I use it?\u003c\/strong\u003e\u003cbr\u003eAs the final coat over prepared deck coating systems on balconies, walkways, parking decks, ramps, and other pedestrian or vehicular traffic surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs it rated for vehicle traffic?\u003c\/strong\u003e\u003cbr\u003eYes, as the wear layer in a traffic-deck system built for pedestrian and vehicular use. Confirm the full assembly and build against your project spec.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"1 Gallon","offer_id":48337440407770,"sku":null,"price":89.9,"currency_code":"USD","in_stock":true},{"title":"5 Gallon","offer_id":48337440440538,"sku":null,"price":449.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9430840836314__5Gallon.png?v=1786908623"},{"product_id":"pts-r12","title":"PTS-R12","description":"\u003cp\u003e\u003cstrong\u003eA low-modulus, water-curable elastomeric membrane that seals interior and exterior surfaces with one product and no mixing.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003ePTS-R12 is a single-component, 100%-solids waterproofing membrane, adhesive, and coating from the PSI Poly-Tuff line. It cures by reaction with atmospheric moisture, so there is no two-part mixing, no measuring, and no pot-life waste. Roll, brush, trowel, or gun it to the thickness the job calls for and it builds a long-lasting, weather-tight seal that stays flexible through extreme temperature swings.\u003c\/p\u003e\n\u003cp\u003eThe chemistry bonds primerless to most common building substrates and grips even damp masonry, which keeps crews moving on real-world job sites. It is low odor and non-gassing, resists dirt pickup, and holds its elasticity from deep cold to summer heat. Use it as a stand-alone membrane, as a high-movement waterproofing layer, or as an elastic adhesive for flashing details and under Flexi-Ply systems.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e single-component, low-modulus, water-curable elastomeric waterproofing membrane, adhesive, and coating\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolids:\u003c\/strong\u003e 100% by weight, 100% by volume\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e White and Grey\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 2 gallon and 5 gallon pails\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e apply not less than 30 mils for membrane and roof coating (about 50 sq ft per gallon); 60 mils for planter box and below-grade work (about 25 sq ft per gallon)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardness:\u003c\/strong\u003e Shore A 30 ± 5 (low modulus)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElongation at break:\u003c\/strong\u003e 300 to 400%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eService temperature:\u003c\/strong\u003e -25°F to 200°F (-32°C to 93°C)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCure:\u003c\/strong\u003e skins in 15 to 45 min; water-cured cures through in 2 to 6 hr; cures in 1 to 2 days without added water\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApply above:\u003c\/strong\u003e 40°F (4°C)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandards:\u003c\/strong\u003e meets ASTM C-836 and E-96; ASTM C-920 Type S, Grade NS, Class 25; primerless on most substrates; bonds to damp masonry\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use\u003c\/h3\u003e\n\u003cp\u003eInterior and exterior roofing, concealed waterproofing, under-tile and under-concrete waterproofing, planter boxes, parapet walls, expansion joints, green roofs, pot-hole filling, and leveling of uneven surfaces. It coats built-up roofing, single-ply, PVC, and SBS modified bitumen, and works as a high-movement waterproofing layer where structures flex.\u003c\/p\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003ePair PTS-R12 with the PSI Poly-Tuff basecoat, topcoat, and reinforcement systems for a complete waterproofing buildout, or run it under Flexi-Ply as the bonded membrane layer.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need to mix anything?\u003c\/strong\u003e\u003cbr\u003eNo. PTS-R12 is single-component and cures by reaction with atmospheric moisture. For heavy builds above 20 mils, or when weather is changing fast and you need a quicker set, blend in 4 to 5 ounces of water per gallon to water-cure it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need a primer?\u003c\/strong\u003e\u003cbr\u003eIt is primerless on most substrates and bonds to damp masonry. Metal should be clean, rust-free, and solvent-wiped; new concrete and masonry should cure 14 days before application.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow thick should I apply it?\u003c\/strong\u003e\u003cbr\u003eNot less than 30 mils for membrane and roof coating applications, and 60 mils for planter box and below-grade waterproofing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow fast does it cure?\u003c\/strong\u003e\u003cbr\u003eIt skins over in 15 to 45 minutes. Water-cured, it cures through in 2 to 6 hours depending on temperature, humidity, and thickness. Used without added water, cure runs 1 to 2 days.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use it on vertical and overhead surfaces?\u003c\/strong\u003e\u003cbr\u003eYes. It is non-sag and can be applied vertical or overhead with a quality caulking gun. Apply when temperatures are above 40°F.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/PTS-R12-Data-Sheet.pdf?v=1786631485\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"White \/ 2 Gallon","offer_id":48337442996442,"sku":"PT-R12-WHITE-2","price":113.63,"currency_code":"USD","in_stock":false},{"title":"White \/ 5 Gallon","offer_id":48337443029210,"sku":"PT-R12-WHITE-5","price":284.11,"currency_code":"USD","in_stock":false},{"title":"Grey \/ 2 Gallon","offer_id":48337443061978,"sku":"PT-R12-GREY-2","price":113.63,"currency_code":"USD","in_stock":false},{"title":"Grey \/ 5 Gallon","offer_id":48337443094746,"sku":"PT-R12-GREY-5","price":284.11,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9430841884890__5Gallon.png?v=1786908625"},{"product_id":"b-tuff-etch","title":"B-Tuff Etch","description":"\u003cp\u003e\u003cstrong\u003eA biodegradable, non-acid etch that profiles and cleans concrete so your primer and membrane actually bond.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eB-Tuff Etch is a concentrated, VOC-free concrete profiling and cleaning solution that opens up the surface without the hazards of muriatic or phosphoric acid. It will not burn skin, will not corrode metal, and rinses away clean, leaving a uniform profile that gives PSI primers, coatings, stains, and sealers the tooth they need to grip. On balconies, breezeways, pool decks, garage floors, and parking structures, it stands in for mechanical grinding on jobs where dust and downtime are not an option.\u003c\/p\u003e\n\u003cp\u003eStart on a dry, structurally sound surface. Apply by pump sprayer and agitate with a stiff bristle broom to drive the etch into the concrete, then power wash to lift the loosened dirt, laitance, and residue. Coverage runs 150 to 200 sq ft per gallon for light-duty profiling and tightens toward 50 to 100 sq ft per gallon for heavy-duty work. Let the deck dry fully before you prime.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e non-acid concrete profiling, etching, and cleaning ahead of coatings, stains, and sealers\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 150-200 sq ft\/gal light duty, 100-150 medium, 50-100 heavy (theoretical)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry:\u003c\/strong\u003e biodegradable, VOC-free, non-fuming, non-hazardous, non-corrosive concentrate\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e pump or sprayer, agitate with a bristle broom, then power wash\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafe handling:\u003c\/strong\u003e will not burn skin or corrode metals\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShelf life:\u003c\/strong\u003e 12 months factory-sealed, stored 60-95°F (15-35°C)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1 gallon jug, 5 gallon pail\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eProfile ahead of a PSI primer such as Enviro-Grip, then build out your B-Tuff or T-Shield membrane and finish with a Top-Shield topcoat.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eIs this safer than acid etching?\u003c\/strong\u003e\u003cbr\u003eYes. It is biodegradable, non-fuming, and non-corrosive. It will not burn skin or attack metal drains and fixtures the way muriatic or phosphoric acid can.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it replace grinding or shot blasting?\u003c\/strong\u003e\u003cbr\u003eFor many coating and sealer jobs it gives you the profile you need without mechanical prep and the dust that comes with it. On heavily contaminated or glazed slabs, mechanical prep may still be required.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I apply it?\u003c\/strong\u003e\u003cbr\u003eSpray it onto a dry surface, agitate with a stiff bristle broom for deeper penetration, then power wash to remove everything it lifts.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow much do I need?\u003c\/strong\u003e\u003cbr\u003ePlan 150 to 200 sq ft per gallon for light profiling, down to 50 to 100 sq ft per gallon for heavy-duty etching.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes the surface need to be dry?\u003c\/strong\u003e\u003cbr\u003eYes. Apply to a dry surface, and let the concrete dry again after rinsing before you prime.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/B-Tuff-Etch-Data-Sheet.pdf?v=1786632736\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"1 Gallon","offer_id":48337473765594,"sku":"PT-BTUFF-ETCH-1","price":42.24,"currency_code":"USD","in_stock":true},{"title":"5 Gallon","offer_id":48337473798362,"sku":"PT-BTUFF-ETCH-5","price":211.24,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9430851846362__5Gallon.png?v=1786908629"},{"product_id":"pts-e-101","title":"PTS E-101","description":"\u003cp\u003e\u003cstrong\u003eA one-part, water-cured joint sealant that guns fast, cures without mixing, and stays flexible from vertical walls to overhead details.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003ePTS E-101 is a single-component, 100% solids, water-curable elastomeric joint sealant for moving and non-moving joints, inside or out. It bonds to a wide range of substrates without priming, skins fast to resist jobsite dirt pickup, and cures to a durable, weather-tight seal that holds through expansion and contraction. With zero shrinkage and no solvents or odor, it is safe to run indoors and in confined spaces.\u003c\/p\u003e\n\u003cp\u003ePick the grade for the joint. E-101 NS (Non-Sag) guns into vertical, overhead, and sloped joints and holds its shape with zero slump. E-101 SL (Self-Leveling) flows out flat in horizontal joints and deck cracks. Clean and dry the joint, set a backer rod to control depth at a 2-to-1 width-to-depth ratio, and gun the sealant in. It bonds to damp masonry, tools easily, and skins in 40 to 50 minutes. Each option ships as a 12-pack case for production sealing.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e single-component, 100% solids, water-curable elastomeric joint sealant\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrades:\u003c\/strong\u003e NS Non-Sag for vertical and overhead, SL Self-Leveling for horizontal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMovement:\u003c\/strong\u003e ASTM C-920, Type S, Grade NS, Class 25\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhysical:\u003c\/strong\u003e Shore A hardness 30 ± 3, elongation 300-400%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCure:\u003c\/strong\u003e tack-free in 40-50 min, service range -40°F to 200°F\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubstrates:\u003c\/strong\u003e concrete, masonry, metal, wood, PVC, EPDM, SBS mod bit, and more, no priming on most\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColors:\u003c\/strong\u003e black, bronze, dark bronze, limestone, stone, tan, grey, white (custom on request)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 12-pack case\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eSeal joints, cracks, and terminations ahead of your PSI membrane, then reinforce with Max-FD Tape or T-Tex 325 where movement is heaviest.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the difference between NS and SL?\u003c\/strong\u003e\u003cbr\u003eNS (Non-Sag) holds its shape in vertical, overhead, and sloped joints. SL (Self-Leveling) flows flat into horizontal joints and deck cracks. Both are 12-packs at the same price.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need a primer?\u003c\/strong\u003e\u003cbr\u003eOn most substrates, no. E-101 bonds to concrete, masonry, metal, wood, and more without priming. Prep metal first by removing rust, scale, and oils.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it need dry weather to cure?\u003c\/strong\u003e\u003cbr\u003eIt is water-curable and bonds to damp masonry, but joints should be clean and free of standing water and contamination before you gun it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow much movement can it handle?\u003c\/strong\u003e\u003cbr\u003eIt meets ASTM C-920 Class 25 with 300 to 400% elongation, so it moves with the joint instead of tearing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShould I use a backer rod?\u003c\/strong\u003e\u003cbr\u003eYes. Set a backer rod about 25% larger than the joint so the sealant seats at a 2-to-1 width-to-depth ratio and avoids three-point adhesion.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/PTS-E-101-Data-Sheet.pdf?v=1786632736\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"NS Non-Sag (12-Pack)","offer_id":48337473831130,"sku":"PT-E101-NS-12","price":120.84,"currency_code":"USD","in_stock":true},{"title":"SL Self-Leveling (12-Pack)","offer_id":48337473863898,"sku":"PT-E101-SL-12","price":120.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-e101.png?v=1786975811"},{"product_id":"max-fd-tape","title":"Max-FD Tape","description":"\u003cp\u003e\u003cstrong\u003eAn elastic polyurethane-foam mesh tape that bridges cracks and joints and hides them under your fluid-applied deck membrane.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eMax-FD Tape is a highly elastic, multi-directional polyurethane foam mesh tape built to mask and reinforce expansion joints, control joints, cracks, seams, and flashings before a PSI coating goes down. It embeds into the wet basecoat and stretches with the substrate, with 300% multi-directional elongation and crack-bridging that outperforms standard reinforcement tapes. In most cases it lets you bridge failed or moving joints without cutting out and replacing old sealant first.\u003c\/p\u003e\n\u003cp\u003eCenter the tape over the joint, crack, or flashing. Lay down a bed of basecoat about 10 mils thick, then gently embed the tape into the wet coating so the resin bleeds through and saturates the mesh. Do not prime over the tape. After two hours or more, apply a second pass of basecoat and feather it smoothly onto the adjacent surface. Coat it the same day it is installed and keep it protected from rain and standing water until it is covered.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e crack, joint, seam, and flashing reinforcement under fluid-applied membranes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoll size:\u003c\/strong\u003e 4 in x 450 ft\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElongation:\u003c\/strong\u003e 300% multi-directional\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThickness:\u003c\/strong\u003e about 0.005 in\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible with:\u003c\/strong\u003e polyurethane, silicone, acrylic, and cementitious coatings\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Poly-Tuff blue\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstall:\u003c\/strong\u003e embed into a ~10 mil wet basecoat, recoat after 2 hours, coat the same day\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e single roll\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eBed it into your B-Tuff or P-Tuff basecoat over detail areas, then carry the field membrane and a Top-Shield topcoat across the deck.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhere do I use it?\u003c\/strong\u003e\u003cbr\u003eOver expansion and control joints, cracks, seams, plywood transitions, flashings, and other high-stress areas that need to move without telegraphing through the membrane.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I prime over it?\u003c\/strong\u003e\u003cbr\u003eNo. Do not prime over Max-FD Tape. Embed it directly into the wet basecoat and topcoat over it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I have to remove old sealant first?\u003c\/strong\u003e\u003cbr\u003eIn normal PSI coating applications, the tape can bridge and hide failed joint sealant without cutting it out first.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow soon do I coat over it?\u003c\/strong\u003e\u003cbr\u003eGive the embedding coat about two hours, then apply the next basecoat pass. Always coat the tape the same day it is installed.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes it stretch in every direction?\u003c\/strong\u003e\u003cbr\u003eYes. It is a multi-directional foam mesh rated at 300% elongation, so it bridges movement in any direction.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/Max-FD-Tape-Data-Sheet.pdf?v=1786632736\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"4 in x 450 ft","offer_id":48337474093274,"sku":"PT-MAXFD-TAPE","price":57.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-maxfd.png?v=1786975810"},{"product_id":"poly-tuff-insta-thick","title":"Poly-Tuff Insta-Thick","description":"\u003cp\u003e\u003cstrong\u003eA lightweight thickening powder that raises the viscosity of your membranes and sealants for vertical, sloped, and overhead work.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003ePoly-Tuff Insta-Thick is an ultra-fine, UV-stable powder that thickens PSI epoxy, urethane, and sealant materials in the field, so a horizontal-grade liquid becomes roller grade, slope grade, vertical grade, or even overhead grade. It builds body without significantly changing the cured physical properties of the coating, which lets you adjust for weather, temperature, and detail work right on the job.\u003c\/p\u003e\n\u003cp\u003eOpen the pail and break apart any lumps. Add the powder slowly into your liquid membrane or sealant and mix until it fully wets out and reaches a smooth, lump-free consistency. Keep adding in small increments until you hit the viscosity you need. Test on a scrap surface with a vertical sag line before you commit, and mix only what you will place the same day.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e field thickener for horizontal membranes, epoxies, urethanes, and sealants\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjusts:\u003c\/strong\u003e roller, slope, vertical, and overhead grade from a horizontal material\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEffect:\u003c\/strong\u003e raises viscosity with minimal change to cured properties\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTraits:\u003c\/strong\u003e lightweight, easily dispersed, UV stable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e medium grey\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMixing:\u003c\/strong\u003e add slowly and mix until fully wet out, use the same day\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShelf life:\u003c\/strong\u003e 6 months factory-sealed, stored 60-95°F (15-35°C), keep dry\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 5 gallon pail\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eThicken B-Tuff, P-Tuff, or T-Shield membranes for vertical walls and details, and body up your PTS E-101 sealant tie-ins where needed.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat does it do?\u003c\/strong\u003e\u003cbr\u003eIt raises the viscosity of liquid membranes and sealants so they hold on slopes, walls, and overhead without sagging.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it change how the coating cures?\u003c\/strong\u003e\u003cbr\u003eNo. It is formulated to build viscosity without significantly altering the cured physical properties of the material.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow much do I add?\u003c\/strong\u003e\u003cbr\u003eAdd slowly in small amounts and mix until you reach the grade you want. Run a vertical sag-line test on a scrap piece to dial it in.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I mix it by hand?\u003c\/strong\u003e\u003cbr\u003eMechanical mixing is recommended for a smooth, lump-free blend. Hand mixing is not recommended.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow long do I have once it is mixed?\u003c\/strong\u003e\u003cbr\u003eUse it the same day it is mixed into the membrane or sealant.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/Poly-Tuff-Insta-Thick-Data-Sheet.pdf?v=1786632736\" target=\"_blank\" rel=\"noopener\"\u003eDownload data sheet (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"5 Gallon","offer_id":48337474912474,"sku":"PT-INSTA-THICK-5","price":50.56,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/9430852010202__5Gallon.png?v=1786908631"},{"product_id":"color-pack-paste","title":"Color Pack Paste","description":"\u003cp\u003e\u003cstrong\u003eA concentrated pigment paste that tints PSI topcoats and membranes to a standard or custom color without weakening the coating.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eColor Pack Paste is a ready-to-disperse pigment concentrate that colors your PSI urethane topcoats and membranes to a consistent standard shade or a custom color match. It stirs into the base material and carries strong, uniform color, so the deck finishes the way the spec calls for, batch after batch.\u003c\/p\u003e\n\u003cp\u003eAdd the paste into the coating and mix thoroughly until the color is fully dispersed and streak-free before you apply. Blend full units at a time to keep color consistent from pail to pail across the job, and mix only what you will use within the working time of the coating.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e color dispersion for PSI topcoats and membranes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e standard shades or a custom color match\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDosing:\u003c\/strong\u003e mixed into the base coating to hit your color target\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMixing:\u003c\/strong\u003e stir until fully dispersed and streak-free\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eForm:\u003c\/strong\u003e pre-dispersed pigment paste\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e 1 quart\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eTint your Top-Shield topcoat or PTS membrane, and keep a matched batch on hand for touch-ups and detail work.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat can I tint with it?\u003c\/strong\u003e\u003cbr\u003ePSI urethane topcoats and membranes that accept a pigment dispersion.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStandard or custom colors?\u003c\/strong\u003e\u003cbr\u003eBoth. Use it for standard shades or a custom match. Confirm the exact ratio with your Latux rep for the color you need.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it affect coating performance?\u003c\/strong\u003e\u003cbr\u003eMixed at the correct dose it colors the material without compromising the coating. Do not overload past the recommended amount.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I keep color consistent?\u003c\/strong\u003e\u003cbr\u003eTint full units at a time and mix thoroughly so every pail matches across the deck.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow much do I add per unit?\u003c\/strong\u003e\u003cbr\u003eDosing depends on the target shade and the coating. Check with your Latux rep for the mix ratio.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"1 Quart","offer_id":48337475109082,"sku":"PT-COLOR-PACK-QT","price":25.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-colorpk.png?v=1786975810"},{"product_id":"p-tuff-catalyst","title":"P-Tuff Catalyst","description":"\u003cp\u003e\u003cstrong\u003eA cold-weather catalyst that speeds the cure of P-Tuff Classic when the temperature drops or the schedule tightens.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eP-Tuff Catalyst is a single-component organometallic liquid that accelerates the moisture cure of P-Tuff Classic basecoat. It doses into the pail to shorten cure time in cold weather or when you need to turn a deck faster. One vial ships free with every pail of P-Tuff Classic, and you can buy extra here for cold-weather work or heavier dosing.\u003c\/p\u003e\n\u003cp\u003eAdd the catalyst to a freshly opened pail of P-Tuff Classic and mix it in thoroughly before you apply. Use roughly up to three vials per 5-gallon pail depending on how cold it is and how fast you need the cure. Colder conditions and tighter turnarounds call for more. Do not exceed the recommended dosing, and mix only what you will place within the working time.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e cure accelerator for P-Tuff Classic single-component basecoat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry:\u003c\/strong\u003e single-component organometallic liquid catalyst\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBenefit:\u003c\/strong\u003e shortens cure time in cold weather and tight schedules\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDosing:\u003c\/strong\u003e up to about 3 vials per 5-gallon pail, adjusted to temperature\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded:\u003c\/strong\u003e one vial ships free with each P-Tuff Classic pail, sold separately here for extra dosing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMixing:\u003c\/strong\u003e stir fully into the pail before application\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackaging:\u003c\/strong\u003e single vial\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUse it with\u003c\/h3\u003e\n\u003cp\u003eDose it into P-Tuff Classic basecoat, then finish the system with your PSI membrane detailing and a Top-Shield topcoat.\u003c\/p\u003e\n\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is it for?\u003c\/strong\u003e\u003cbr\u003eIt speeds up the cure of P-Tuff Classic in cold weather or when you need to turn the deck faster.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I have to buy it?\u003c\/strong\u003e\u003cbr\u003eEvery P-Tuff Classic pail already includes one free vial. Buy extra here for cold conditions or heavier dosing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow much do I add?\u003c\/strong\u003e\u003cbr\u003eUp to about three vials per 5-gallon pail, more for colder temperatures and faster cures. Do not exceed the recommended dose.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhich product does it work with?\u003c\/strong\u003e\u003cbr\u003eIt is made for P-Tuff Classic single-component basecoat.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow do I mix it in?\u003c\/strong\u003e\u003cbr\u003eAdd it to a freshly opened pail and stir thoroughly until fully blended before you apply.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eDistributed and supported by Latux.\u003c\/em\u003e\u003c\/p\u003e","brand":"PSI","offers":[{"title":"Vial","offer_id":48337475174618,"sku":"PTCATVL","price":1.43,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/3178\/9786\/files\/gh-catalyst.png?v=1786975811"}],"url":"https:\/\/latuxepoxy.com\/collections\/psi.oembed","provider":"Latux Epoxy","version":"1.0","type":"link"}