More in PremeraView all
Premera · Polyaspartic
At a glance
- SKU
- PREMERA-FP1-1G
- Vendor
- Premera
- Coverage
- 300 to 400 sq ft per gallon at 0.4 to 0.9 mils dry
- Overcoat window
- 90 minutes, top while tacky
- VOC
- under 150 g/L, single component
- Weight
- 10.0 lb
WarrantyIf a product is defective or does not perform to its published specs, we replace it. Limited Warranty
Technical helpMix ratios, install questions, job-site troubleshooting. Mon to Fri, 8 to 5 EST.Contact a pro
Premera · Primer
Premera FP1 Fusion Primer for Epoxy and Polyaspartic
Premera FP1 Fusion Primer is a single-component sol-gel primer that chemically fuses to clean, sound concrete and to existing coatings, so you can prime without grinding. It yields 300 to 400 sq ft per gallon and runs under epoxy, metallic epoxy, and polyaspartic systems while staying UV stable under clear topcoats.
$175.00
Size 1 Gallon
Big job or contractor pricing? Request a quote
- Free UPS Ground on orders $150+, or free pickup in Pompano Beach, FL
- Free replacement if your order arrives damaged or we ship the wrong item. Let us know within 48 hours of delivery with photos. Replacement Policy
New customer? Get 10% off your first order
- UV Stable UV Stable
- Family-Run Since 2004 20+ years in the trade
At a glance
Premera FP1 Fusion Primer for Epoxy and Polyaspartic
Premera FP1 Fusion Primer is a single-component sol-gel primer, a coat that chemically fuses to clean, sound concrete and to existing coatings so you can prime without grinding the whole slab. It is built for installers running epoxy, metallic epoxy, and polyaspartic systems who need a fast bonding primer that stays UV stable under clear topcoats.
300-400
SQ FT/GAL
At 0.4 to 0.9 mils dry
90
MIN WINDOW
Overcoat while tacky
NO
GRINDING
On clean, sound concrete
<150
G/L VOC
Single component
What makes it work
A primer that bonds without a grinder
Fuses chemically
The sol-gel builds a molecular bridge to clean, sound concrete, so you prime with no grinding instead of opening the whole slab.
Works as an intercoat primer
Bonds an existing coating to your next layer, so you can recoat a floor without stripping it back to bare concrete.
Wide compatibility
Runs under epoxy, metallic epoxy, polyaspartic, and solvent-based coatings, and stays UV stable under clear tops.
Watch the window
Flashes tacky in 15 to 20 minutes at 72F and tops within a 90 minute overcoat window. Miss it and you screen and re-prime.
COVERAGE AND APPLICATION
| Coverage | 300 to 400 sq ft per gallon at 0.4 to 0.9 mils dry |
| Porous concrete | Two coats wet-on-wet, 2 to 3 mils each |
| Non-porous surfaces | One coat, 1 to 2 mils, 50% overlap |
| Application temperature | 45 to 104F |
CURE AND RECOAT
| Tacky | 15 to 20 min at 72F |
| Touch dry | 90 min |
| Dry-through | 120 min |
| Recoat | 5 to 90 min |
| Overcoat window | 90 minutes, top while tacky |
COMPOSITION AND COMPATIBILITY
| Chemistry | Single-component sol-gel, ready to use, no backroll |
| Coats over | Epoxy, metallic epoxy, polyaspartic, solvent-based. UV stable |
| Not compatible | Water-based topcoats. Use solvent-based or 100% solids over FP1 |
| New concrete under 28 days | Use Easy MVB first, coat 96 hours after pour |
| VOC | Under 150 g/L, under 1.25 lb/gal. Flash point under 77F |
| Cleanup | Acetone |
Kit to floor
Build the complete system.
What comes in the box, and what goes under and over it. Add any step to your cart from here.
Pairs with
Prime over Premera Easy MVB on slabs with a moisture question, then follow with your epoxy, metallic, or polyaspartic and a Premera T2 topcoat. Use solvent-based or 100% solids coatings over FP1, not water-based tops.
1Prep the slab
You are here
Premera FP1 Fusion Primer for Epoxy and Polyaspartic
$175.00This item
2Base coat
Everflow EF-100
$179.99
3Add a lookoptional
4Topcoatfor UV or extra gloss
Everflow EF-275
$199.00Sold out
Does FP1 need grinding?
No. The sol-gel fuses chemically to clean, sound concrete, so you can prime without grinding the whole slab.
What systems does it work under?
Epoxy, metallic epoxy, polyaspartic, and solvent-based coatings, and it stays UV stable under clear tops.
Can I use it as an intercoat primer?
Yes. It bonds an existing coating to your next layer, so you can recoat without stripping to bare concrete.
What is the overcoat window?
It flashes tacky in 15 to 20 minutes at 72F and tops within a 90 minute window. Miss it and you screen and re-prime.
Is it compatible with water-based topcoats?
No. Use solvent-based or 100% solids coatings over FP1, not water-based tops.
What about new concrete?
On new concrete under 28 days, use Easy MVB first and coat 96 hours after the pour.
Recently viewed
