More in EverflowView all
EF-100Epoxy Floor Coatings
EF-280Polyaspartic Top Coats
EF-275Polyaspartic Top Coats
EF-MasterflowEpoxy Kits
EF-135Crack Filler
EF-290Polyaspartic Top Coats
EF-285Primer
EF-195Deep Pour Epoxy
EF-191Countertop Epoxy
EF-155Epoxy Floor Coatings
EF-160Moisture Vapor Barrier
EF-301Polyurethane Finish Coat
EF-150Epoxy Floor Coatings
Everflow · EF-275
At a glance
- SKU
- POLYFLOW-275
- Vendor
- Everflow
- Finish
- UV-Stable Clear
- Recoat
- 2 to 4 hrs
- Abrasion
- 0.03 g (Taber)
- Coverage
- About 400 sq ft per 2-gal kit
- Working time
- 20 to 25 min at 70°F
- Weight
- 19.8 lb
WarrantyIf a product is defective or does not perform to its published specs, we replace it. Limited Warranty
Technical helpMix ratios, install questions, job-site troubleshooting. Mon to Fri, 8 to 5 EST.Contact a pro
Everflow · Polyaspartic Top Coats
Everflow EF-275
Solvent Based Polyaspartic (2gal)
EF-275 is Everflow's solvent-based aliphatic polyaspartic topcoat, a crystal-clear, UV-stable clear coat that seals solid-color coatings and vinyl flake floors with superior abrasion, chemical, and UV resistance. It cures fast enough to reopen the space the same day, stays low-VOC under 100 g/L, and meets CFIA and USDA requirements for indirect food contact.
$199.00
Big job or contractor pricing? Request a quote
- Free UPS Ground on orders $150+, or free pickup in Pompano Beach, FL
- Free replacement if your order arrives damaged or we ship the wrong item. Let us know within 48 hours of delivery with photos. Replacement Policy
New customer? Get 10% off your first order
- CFIA / USDA Indirect Food Contact Meets CFIA and USDA requirements for indirect food contact
- LEED v4 Low-Emitting SCAQMD Method 304-91
- VOC Compliant (<100 g/L) VOC Compliant (<100 g/L)
- ASTM Tested Full test data on the TDS
- Family-Run Since 2004 20+ years in the trade
At a glance
Everflow EF-275
EF-275 is a solvent-based polyaspartic clear coat in a 2-gallon kit, made to seal epoxy, solid-color and vinyl flake floors. Garages, shops and commercial spaces that need to reopen the same day. It won't yellow or chalk, and one kit covers about 400 sq ft over an existing coating.
Previously sold as MPC-275. Same topcoat, same manufacturer, new name.
75%
SOLIDS
Builds a protective clear film
0.03
G TABER LOSS
Low abrasion wear (CS-17)
40%
ELONGATION
Flexes without cracking
89.5
GU GLOSS
Crystal-clear high-gloss
What makes it work
Same-day clear coat for flake and color floors
UV-stable clear finish
Aliphatic polyaspartic chemistry resists yellowing and chalking for a crystal-clear, high-gloss finish that holds up indoors and out.
Same-day return to service
Recoat in 2 to 4 hours and walk on it in 4 to 8, so you can reopen the space the same day.
Superior abrasion and chemical resistance
Just 0.03 g of Taber abrasion loss protects the color and flake beneath from foot and cart traffic.
Built for flake and color systems
The go-to thin clear topcoat over vinyl flake broadcast (chip) floors and solid-color coatings.
Flexible and tough
40% elongation at break resists cracking, with 5,150 psi tensile and about 0.75 DCOF wet traction.
The difference
Which topcoat do you need?
| TOPCOAT | EF-275 (this product) | EF-280 | EF-285 | EF-290 | EF-301 |
| Solids | 75% | 80% | 85% | 90% | 85% |
| Finish and gloss | High-gloss clear, 89.5 GU | High-gloss clear, 89.5 GU | High-gloss clear, 89.5 GU | High-gloss clear, 89.5 GU | Satin, 35 GU |
| Coverage per kit | About 400 sq ft over coating, 2-gal kit | About 600 sq ft over coating, 3-gal kit | About 400 sq ft at 8 mils, 2-gal kit | About 400 sq ft over coating, 2-gal kit | 350 to 450 sq ft, 1-gal kit |
| Recoat window | 2 to 4 hr | 2 to 4 hr | 2 to 4 hr | 2 to 4 hr | Applied as the final coat |
| Foot traffic | 4 to 8 hr | 4 to 8 hr | 4 to 8 hr | 3 to 6 hr | About 1 day |
| UV stability | UV stable, non-yellowing | UV stable, non-yellowing | UV stable, non-yellowing | UV stable, non-yellowing | UV stable, non-yellowing |
| Best for | Fast, budget-friendly clear over flake and color floors | All-around kit with the most coverage per kit | VOC-strict states, under 50 g/L, and UV-stable priming | Thickest clear coat, fewest coats | Satin-capable final finish that hides scuffs |
Planning the job
Coverage and cure.
Per 2-gallon kit. Real coverage depends on concrete porosity and the profile of the slab.
Over coating8 mils
~400
sq ft per kit
Over vinyl flake12 mils
~267
sq ft per kit
Cure at 68°F
Working time 20 to 25 min at 70°F2 to 4 hrRecoat
4 to 8 hrFoot traffic
About 1 dayVehicle traffic
About 7 daysFull cure
Warmer temperatures speed this up; cooler temperatures slow it down.
PHYSICAL AND CHEMISTRY
| Type | Solvent-based aliphatic polyaspartic polyurea, 2-component |
| Solids | 75% by weight |
| Finish and gloss | Crystal-clear high-gloss, 89.5 GU at 60 degrees |
| Color | Crystal-clear |
| Viscosity | Part A 200 to 300 cps, Part B 50 to 100 cps |
MECHANICAL
| Abrasion (Taber CS-17) | 0.03 g loss (ASTM D4060) |
| Elongation at break | 40% (ASTM D638) |
| Tensile strength | 5,150 psi (ASTM D638) |
| Pull-off adhesion | Over 363 psi, substrate failure (ASTM D7234) |
| Hardness | Koenig pendulum 175 sec at 8 mils (ASTM D4366) |
| Slip resistance (DCOF) | About 0.75 wet (ASTM E303-93) |
APPLICATION AND CURE
| Working time | 20 to 25 min at 70 degrees F, 50% RH |
| Cure at 68 degrees F | Recoat 2 to 4 hr, foot 4 to 8 hr, vehicle about 1 day, full about 7 days |
| Coverage | Over coating 8 mils about 400 sq ft, over vinyl flake 12 mils about 267 sq ft per 2-gallon kit |
| Application | 10 mm roller or squeegee over a prepared base system, not bare concrete |
| Apply temperature | 41 to 86 degrees F |
COMPLIANCE
| VOC | Under 100 g/L (LEED v4 low-emitting, SCAQMD 304-91) |
| Food contact | Meets CFIA and USDA requirements for indirect food contact |
| Shelf life | 1 year unopened, store 59 to 86 degrees F |
Kit to floor
Build the complete system.
What comes in the box, and what goes under and over it. Add any step to your cart from here.
In the kit
- 2-gallon kit: 3.78 L resin (Part A) plus 3.78 L hardener (Part B)
- Two-component system, mix only what you can spread in 20 to 25 minutes
- Crystal-clear base, supplied clear only
Pairs with
Seal an EF-100 base coat or a vinyl flake broadcast from our 25 lb flake box with EF-275. On a damp slab, lay down EF-160 moisture vapor barrier first. Diamond grind concrete to ICRI CSP-2 and build the base before the clear coat.
1Prep the slab
Everflow EF-160
$192.00Sold out
2Base coat
Everflow EF-100
$179.99
3Add a lookoptional
4Topcoatfor UV or extra glossYou are here
Everflow EF-275
$199.00This item
5Tools
Latux Flat Squeegee
$35.00
What is EF-275 used for?
It's a UV-stable clear topcoat applied over solid-color coatings and vinyl flake (chip) systems to seal in the finish and protect it from wear, chemicals, and sunlight. It's the final clear layer of a floor system, not a base coat.
Will EF-275 turn yellow?
No. As a true aliphatic polyaspartic, it resists yellowing and chalking and keeps a crystal-clear, high-gloss finish in both interior and sun-exposed applications.
How quickly can I reopen the floor?
Fast, at 68°F you can recoat in 2 to 4 hours, allow foot traffic in 4 to 8 hours, and vehicle traffic in about a day. Full cure is roughly 7 days.
Can I apply EF-275 directly on concrete?
No, it's a topcoat, not recommended for use directly on bare concrete. Apply it over a prepared base coat or flake system. Make sure the slab has a moisture barrier to avoid delamination.
How much does one kit cover?
A 2-gallon kit covers about 400 sq ft at 8 mils over an existing coating, or about 267 sq ft at 12 mils over a vinyl flake broadcast system.
Can I get EF-275 in a color?
No. EF-275 ships crystal clear only, and Latux does not offer a color pack for it. Build the color into the layer underneath with a solid-color base coat or a vinyl flake broadcast, then seal it with EF-275 as the clear topcoat.
Why are there tire marks on my polyaspartic floor?
Rubber tires can stain a polyaspartic coating through plasticizer migration, and quick stops or starts can leave rubber burn marks. This is normal for clear coatings; use floor mats under vehicles where staining is a concern.
What is the working time after mixing?
About 20 to 25 minutes at 70°F. Mix only what you can spread within that window and never leave mixed product in the bucket.
Is polyaspartic better than epoxy for a garage floor?
They do different jobs. Epoxy like EF-100 builds the base and bonds to the concrete. Polyaspartic goes on top as the clear coat: it won't yellow in sunlight and it resists abrasion, with just 0.03 g Taber loss. Most garage systems use both. See our Polyaspartic vs Epoxy guide.
How many EF-275 kits do I need for a 2-car garage?
A typical 2-car garage runs about 400 to 500 sq ft. Over an existing coating at 8 mils one kit covers about 400 sq ft, so plan on 1 to 2 kits. Over a vinyl flake broadcast at 12 mils a kit covers about 267 sq ft, so plan on 2 kits.
What's the difference between EF-275 and EF-280?
Same UV-stable polyaspartic performance. EF-275 is the 2-gallon kit at 75% solids for thin clear coats. EF-280 is the 3-gallon kit at 80% solids and covers more floor per kit, about 600 sq ft.
What temperature can I apply EF-275 in?
Apply between 41 and 86°F. Working time is 20 to 25 minutes at 70°F and gets shorter when it's hot, so mix small batches on warm days.
Is EF-275 slippery when wet?
It tests at about 0.75 DCOF wet (ASTM E303-93). Keep in mind a high-gloss clear coat over a smooth base will feel slicker than a textured flake floor.
What is the VOC content?
Under 100 g/L, LEED v4 low-emitting. If your state has a stricter VOC limit, EF-285 is under 50 g/L.
How does shipping work?
Free UPS Ground shipping on orders of $150 or more. A single EF-275 kit qualifies. You can also pick up free at our Pompano Beach warehouse. For large jobs or contractor pricing, message your Latux rep.
Recently viewed